Plaster-clad homes explained

Monolithic Cladding: A Guide for NZ Homeowners

Monolithic cladding is a seamless, plaster-look exterior finish, usually a textured coating over rigid sheets such as fibre cement or polystyrene, with no visible joints or overlapping boards. It was common on New Zealand homes built from the mid-1990s to the mid-2000s, and many direct-fixed systems from that era became part of the leaky homes problem. Well-built and well-maintained monolithic homes can perform well.

For New Zealand owners and buyers of plaster-clad and monolithic homes.

A monolithic clad home in Wellington after repairs and a new coating system by Refresh Painters
Monolithic home renewal: targeted repairs, a complete exterior coating system and a crisp new finish.

What is monolithic cladding?

"Monolithic" means one continuous surface. Instead of weatherboards or bricks, the wall is finished with a coating that hides the joints. Common types in New Zealand include:

  • Fibre cement sheet systems finished with a textured coating
  • EIFS (polystyrene) systems: polystyrene sheets with a mesh-reinforced plaster finish
  • Solid plaster or stucco over a backing and mesh

The look stayed popular because it suits modern and Mediterranean designs. What matters for the life of the house is how the system was installed and detailed, and how well it has been looked after.

How to tell if your house has monolithic cladding

  • Smooth or textured plaster-look walls with no visible board lines
  • Tap the wall: a hollow sound often means sheet or polystyrene behind the coating; solid plaster sounds dull and hard
  • Built or reclad between about the mid-1990s and mid-2000s
  • Few or narrow eaves, flat roofs, parapets or enclosed decks
  • The council property file or a builder's report names the cladding system

Monolithic cladding problems: why some homes leaked

Many homes from that era had monolithic cladding fixed straight onto untreated timber framing with no gap behind it. When water got in through cracks, joints, window junctions or poorly flashed details, it had no way to drain or dry, and the framing could rot. A 2008 PricewaterhouseCoopers report to the Government estimated the leaky building problem at around NZ$11.3 billion across about 42,000 buildings.

Common entry points are:

  • Window and door junctions without proper flashings
  • Cracks in the coating
  • Parapets, enclosed balconies and decks over living spaces
  • Pipe and fixing penetrations with failed sealant
  • Cladding taken down to the ground or into the deck

Signs to watch for include staining under windows, swollen skirtings, soft or bulging plaster, musty smells and recurring cracks.

Cavity or direct-fixed: the question that matters most

A drained cavity is a gap, nominally 20 mm, between the cladding and the framing, so water that gets past the cladding can drain away and the wall can dry. MBIE's compliance document for Building Code clause E2 (External Moisture) introduced drained cavities into its acceptable solution with the third edition of E2/AS1, which took effect on 1 July 2005, with a risk matrix deciding which walls needed one. A 2011 amendment then made a drained cavity standard behind all monolithic claddings.

Homes built with a cavity are generally far lower risk. Direct-fixed homes from before then are the ones that need the closest attention. A building surveyor can usually tell you which you have.

Monolithic cladding vs weatherboard

Monolithic cladding vs weatherboard at a glance
PointMonolithicWeatherboard
LookSeamless, modernLapped boards, traditional
How it sheds waterRelies on the coating, sealants and flashingsBoards overlap and shed water outward
MaintenanceKeep the coating continuous, repair cracks, renew sealantsRepaint, replace rotten boards, keep timber sealed
Risk eraDirect-fixed systems roughly mid-1990s to mid-2000sLower risk; problems are usually local rot

Monolithic cladding vs stucco and roughcast

Stucco and roughcast are older solid plaster finishes: cement plaster applied over a backing, often with wire mesh, and roughcast has a coarse, pebbly texture. They are heavy, hard finishes found on many older NZ homes. Modern monolithic systems are usually lighter sheet-based claddings with a thinner textured coating. All of them rely on a sound coating, sealed cracks and good flashings to keep water out, and all are repaired and recoated in a similar way.

If you own a weatherboard home, our weatherboard and character home repaints page covers its care.

Looking after a monolithic house

A monolithic wall stays weathertight only while its coating, joints and sealants stay intact. A simple routine:

  • Wash yearly to remove dirt, mould and salt, especially on sheltered walls.
  • Check after winter for new cracks, especially at window corners and sheet lines.
  • Renew failed sealant around windows, pipes and fixings.
  • Repair cracks early with compatible flexible fillers; see how exterior plaster repair is done.
  • Recoat on time: most exterior coatings need attention around every 7 to 10 years, and on monolithic homes a compatible system matters.
  • Keep ground and decks clear of the bottom edge of the cladding.

We are STO accredited and carry out monolithic cladding painting with compatible coating systems.

Repair, recoat or reclad: who does what

The right answer depends on whether the framing behind the cladding is sound.

  • Building surveyor or moisture specialist: investigates, tests moisture and tells you whether the framing is affected.
  • Painter and plaster repairer (that is us): repairs suitable non-structural cracks and damage, renews sealant within our scope and recoats with a compatible system when the substrate is sound.
  • Licensed builders and remediation specialists: carry out recladding and structural repairs. Recladding is building work that needs a building consent from your council.

We do not do full recladding or structural remediation, but we coordinate our coating work around it. Learn more about our monolithic repair service in Wellington.

Monolithic cladding repair and recoat costs in NZ

Costs swing widely with the size of the house, its condition and what an investigation finds. These are the ranges published NZ guides give:

Typical NZ costs for monolithic homes (published guides, 2025 to 2026)
WorkTypical range
Recoating sound plaster or monolithic claddingUsually at the upper end of exterior painting prices, which run about $30 to $90 per m2 of wall
Exterior plaster repairAbout $70 to $180 per m2 of repaired area, depending on the system and damage
Full reclad of a monolithic homeCommonly quoted at $150,000 to $400,000 or more

The gap between those numbers is why early repairs and on-time recoating matter. Pre-purchase and moisture testing reports are a small cost by comparison. For a full breakdown of repaint pricing, see our guide to exterior house painting cost.

Buying a monolithic house: what to check

  • Ask whether the cladding is direct-fixed or on a cavity, and when it was built or reclad.
  • Get a pre-purchase report from an inspector experienced with monolithic homes, with invasive moisture testing where advised.
  • Check the council property file for the code compliance certificate and any reclad consent.
  • Look at the condition of the coating, cracks and sealants.
  • Talk to your lender and insurer early: some ask for a building report on monolithic homes before they lend or insure, and the report's findings can affect the terms.
  • Budget for regular maintenance and recoating.

Your questions

What is monolithic cladding in NZ?

A seamless plaster-look exterior, usually a textured coating over fibre cement or polystyrene sheets, with no visible joints. It was common on homes built from the mid-1990s to the mid-2000s.

Are all monolithic homes leaky?

No. Problems are concentrated in direct-fixed systems without a drained cavity and with poor detailing. Homes built on a cavity, and well-maintained homes, can perform well.

Can monolithic cladding be painted?

Yes, when the substrate is sound. It should be repaired first and coated with a compatible system, often a flexible membrane, so the coating stays continuous.

How often should a monolithic house be repainted?

Most exterior coatings need attention around every 7 to 10 years, depending on the system and exposure, with yearly washing and checks in between.

How much does it cost to fix monolithic cladding?

Published NZ guides put plaster repairs at about $70 to $180 per square metre of repaired area, with recoating priced on top. A full reclad is commonly quoted at $150,000 to $400,000 or more.

Do you reclad monolithic homes?

No. Recladding and structural remediation need licensed building specialists and a building consent. We repair suitable non-structural damage and recoat.

Let’s talk about your place

Keep your monolithic home sealed and looking sharp.

Tell us about your cladding, any cracks and your suburb. We will inspect, explain what can be repaired and recoated, and give you a clear quote.

About this guide

Refresh Painters is an STO-accredited painting team in Johnsonville that repairs and recoats monolithic and plaster homes across Wellington. We wrote this guide in November 2026 using MBIE's E2 compliance document, published reporting on the leaky homes problem and our own repair and coating work. If anything here needs correcting, email tyler@refreshpainters.co.nz.